Frequency Measuring Test Success Does Not Require Sophisticated Equipment
In April 12, ARRL will conduct the Frequency Measuring Test (FMT), a tradition that dates back to 1931. In that era, prospective participants were promised “a pleasant and profitable experience” and advised that taking part in the FMT would be a form of insurance against out-of-band operation “and the unpleasant consequences that follow.” Official Observers and Official Relay Stations were required to participate in the FMT or offer a darn good excuse. W1MK — the predecessor to W1AW — was one of a dozen or so transmitting stations. The 80- and 40-meter frequencies were confirmed through an arrangement with the US Department of Commerce Radio Division.
Accurate frequency measurement — at least to the degree that radio amateurs rarely worry about operating outside of an amateur allocation — now is almost a given. But today’s FMT leaders are able to accurately measure beyond the number of decimal places (out to 5) a typical transceiver will display. FMT announcements may conjure visions of a vast array of sophisticated laboratory equipment. However, while some of the most successful stations did have laboratory-grade gear, others got quite close with far less hardware.
FMTs take place in April and November. The November 2018 FMT results are available on the ARRL website. The actual frequencies were 3,598,726.31 kHz on 80, and 7,064,327.23 on 40.
Tom Wilheit, WX4TW, one of those measuring the 80- and 40-meter frequencies of transmitting station K5CM on November 8 to within 1 Hz or less, reported using an Elecraft KX3 transceiver and Spectrum Lab audio spectrum analysis software. Others used a similar approach. James Keeth, AF9A, reported using an “openHPSDR Mercury receiver, a 10 MHz OCXO reference calibrated against CHU and WWV, and WSJT-X frequency mode for measurements.”
Jim Michener, K9JM, depended on his Elecraft K3 and tuning forks to get within 1 Hz of the mark on both bands. Grady Harper, AJ4YA, got extremely close by zero-beating the signal on his K3 and adjusting the measured frequency “to correct for errors in my tuner.”
“This is my first try with this type of adjustment,” Harper said. “The fractional part of the Hz is based on length of time between beats. I guessed at this part.”
If you’ve never entered an FMT before, Connie Marshall, K5CM, offers informationon his website on how to measure the frequency of a carrier. Articles in QST also have covered this topic.
The April 2019 FMT will get under way at 0200 – 0225 UTC on April 12. The 40-meter frequency will be in the vicinity of 7065 kHz, and the 80-meter frequency will be in the vicinity of 3599 kHz. Details are on page 94 of April QST.
Source:ARRL
(adsbygoogle = window.adsbygoogle || []).push({});
April 06, 2019 No comments
Italab HERCULES 1500 – HF RF POWER AMPLIFIER (1.8 – 30 MHz ) Extremely robust HF RF POWER amplifier, the RF section is equipped with 2 DUA... Read more
April 05, 2019 No comments
RigExpert Stick 60kHz – 35MHz Analyzer | State-of-the-Art Antenna & Cable Analyzer Key Features: Frequency range: 0.06 to 35 MHz, upgradable... Read more
March 18, 2019 No comments
Ailunce HS1 Description: Spectrum Dynamic Waterfall Display Multiple Working Modes：Receive Mode, Transmit Mode, TUNE Mode, VFO Mode, SPLIT Mode DSP Di... Read more
March 09, 2019 No comments
The splitter or combiner is a very useful device. It can provide equal voltages, equal current, or equal power to matched or unmatched loads. Like all... Read more
April 09, 2019 No comments
The winning article for the April 2019 QST Cover Plaque award is “A High-Power 160- and 80-Meter Transmitting Loop Antenna” by Steve Adler, VK5SFA. Th... Read more
April 04, 2019 No comments
April 04, 2019 No comments
Model KA1-DP Gain/Size Frequency Range 7-50 Element 1 Number of Elements for Each Band 7-50MHz DP Longest Element（m） 10.4 Power Rating 7/10MHz 1.2kW S... Read more
March 12, 2019 No comments
Discover the BIG SIGNAL DX-Quad antenna , this new design of a single element Multi-Band Quad covers up to 5 bands in HF from 10 to 20 meters. An incr... Read more
(adsbygoogle = window.adsbygoogle || []).push({});
April 09, 2019 No comments
SOTABeams Features Fully adjustable audio band-pass filtering instantly adjustable for voice, data and CW (b/w 50 Hz to 5 kHz) VIDEO State-of-the-art... Read more
![Covering the Rules on Calling CQ [ ARRL PODCAST ]](https://64.media.tumblr.com/8c43427a62051df18a45ae637508c9af/tumblr_inline_pprqe7t7bS1tixq2a_250.jpg)
April 04, 2019 No comments
April 04, 2019 No comments
The FAA-450 Antenna Analyzer is an open source project built from STM32-F7 Discovery board. This project originated from “EU1KY Antenna Analyzer V3”,... Read more
April 02, 2019 No comments
April 10, 2019 No comments
In April 12, ARRL will conduct the Frequency Measuring Test (FMT), a tradition that dates back to 1931. In that era, prospective participants were pro... Read more
April 09, 2019 No comments
The bidding has begun in the Out of This World ARISS Auction, which wraps up on April 14 at 2200 UTC. A new JVC Kenwood TS-890S is attracting many bid... Read more
April 09, 2019 No comments
The May issue of Digital QST is now available for viewing on your desktop or laptop. Click here to view the issue. It is also available for reading on... Read more
April 09, 2019 No comments
Yet again the monthly IARU-R1 Monitoring System newsletter reports on the severe problems being caused by the Russian OTH radar “Contayner” on 14 MHz... Read more
The post Frequency Measuring Test Success Does Not Require Sophisticated Equipment appeared first on QRZ Now - Amateur Radio News.
from DXER ham radio news http://bit.ly/2UuJNry via IFTTT
